Powered by modern, world-class detection technology
The Honeywell System Sensor series of powerful yet user-friendly speciality detectors use state-of-the-art technology to provide reliable detection in all kinds of fire situations. Each detector in the range provides both audio and visual alarm signals, ensuring that people have the time they need to escape a fire before it can spread and cause irreversible harm.
Reliable 3-fold protection from fires: Heat, Smoke and CO Versatile range with tamper-resistant designs and world-class engineering for dependable protection from the 3 critical aspects of dangerous fires.
Photoelectric Intrinsically-safe Smoke Detector
JTY-GD-2151EIS
The JTY-GD-2151EIS conventional, intrinsically-safe photoelectric smoke detector from Honeywell System Sensor features a state-of-the-art sensing chamber. The detector is designed to provide open area protection and is for use with 2-wire control panels via interface module. It is equipped with two LEDs that provide a local, visual indication of detector status. Once the detector senses a fire, it latches on to the alarm state and remains there until it is reset by a momentary power interruption. The detector can be tested by activating an internal reed switch with a test magnet.
Exia II CT6
360° visible LED indicator
Tamper-resistant design
SEMS screws for easy wiring (B401 plug-in detector base)
The JTWB-BCD-5151EIS is a conventional 2-wire intrinsically safe thermal detector, designed to provide open area protection. It is for use with 2-wire control panels via interface module. The detector utilises a state-of-the-art thermistor sensing circuit for fast and accurate response. It can be used in various environmental conditions and offers the advantages of simple maintenance and lower fault rate. Two red LEDs blink in standby status for 5 seconds each, latch on in alarm and stop blinking in fault.
Exia II CT6
360°visible LED indicator
Tamper-resistant design
SEMS screws for easy wiring (B401 plug-in detector base)
Honeywell System Sensor JTYJ-GD-2330/B is a battery-operated smoke detector. It utilises photoelectric sensing technology to give early warning of developing fires, providing precious escape time before a fire can spread. When the smoke concentration on the site reaches the alarm threshold or the test button is pressed and held down, the alarm’s LED will turn from slow flashing to quick flashing and also give out sound alarm signals. When the smoke concentration drops below the alarm threshold or the test button is released, the alarm will recover to its normal state.
Both audio and visual alarm signals will be given in case of fire
Sound alarm in case of low battery or in the event of photoelectric chamber failure
Test button for self-testing
Foolproof design that resists base closing unless batteries are installed
6-wire Carbon Monoxide (co) Detector With Realtest® Technology
CO1224T
When dangerous amounts of CO are detected, the CO1224T CO detector alerts residents by sounding and flashing a temp 4 signal alarm. Powered by RealTest® technology, the CO gas sensing cell in the device can be tested using a CO gas agent. With 24/7 central station monitoring, residents are guaranteed protection whether they’re away from home, sleeping or already suffering from the effects of CO. The device offers a code-required trouble relay to send a sensor failure or end-of-life signal to the control panel and central station. As a As 12/24 V DC detector, the CO1224T will operate on most industry security and fire alarm control panels.
RealTest® enables functional testing using canned CO
Code-required trouble relay
Wiring supervision with SEMS terminals
Low current draw of 20 mA in standby and 40 mA in alarm
6-wire Carbon Monoxide (co) Detector With Realtest® Technology – Round
CO1224TR
When dangerous amounts of CO are detected, the CO1224TR CO detector alerts residents by sounding and flashing a temp 4 signal alarm. Powered by RealTest® technology, the CO gas sensing cell in the device can be tested using a CO gas agent. With 24/7 central station monitoring, residents are guaranteed protection whether they’re away from home, sleeping or already suffering from the effects of CO. The device offers a code-required trouble relay to send a sensor failure or end-of-life signal to the control panel and central station. As a As 12/24 V DC detector, the CO1224TR will operate on most industry security and fire alarm control panels.
RealTest® enables functional testing using canned CO
Code-required trouble relay
Wiring supervision with SEMS terminals
Low current draw of 20 mA in standby and 40 mA in alarm
