Honeywell fire

FCM-1

Control Module

The FCM-1 from Honeywell NOTIFIER is an intelligent addressable control module that provides supervised monitoring of wiring to load devices that require an external power supply to operate, such as horns, strobes or bells. It is capable of Class A and Class B supervision. Addressability allows the module to be activated, either manually or through panel programming, on a select (zone or coverage area) basis.

SEMS screws for easing wiring
Panel controlled status LED
Analogue communications
Rotary address switches
Low standby current
Mounts in standard 4 " junction box

Download Brochure

FRM-1

Relay Module/p>

The FRM-1 from Honeywell NOTIFIER provides the system with a dry-contact output for activating a variety of auxiliary devices, such as fans, dampers, control equipment, etc. It uses one of 159 possible module addresses on a SLC loop. Addressability allows the dry contact to be activated, either manually or through panel

SEMS screws for easing wiring
Panel controlled status LED
Analogue communications
Rotary address switches
Low standby current
Mounts in standard 4 " junction box

Download Brochure

FTM-1

Firephone Control Module

The FTM-1 from Honeywell NOTIFIER provides the Fire Alarm Control Panel the capability to monitor and control a circuit of up to two firefighter phones. It has the ability to differentiate between normal, off-hook, and trouble conditions. This module is used to connect a remote firefighter telephone to a centralised telephone console. This module has two pairs of output termination points available for fault-tolerant wiring (Style Z), and includes a panel-controlled LED indicator.

Built-in type identification automatically identifies itself to the control panel
Direct-dial entry of address 01– 159 for FlashScan®
Internal circuitry and relay powered directly by two-wire SLC loop
High noise immunity (EMF/RFI)
Wide viewing angle of LED

Download Brochure

FMM-1

Intelligent Monitor Module

The FMM-1 from Honeywell NOTIFIER is an intelligent monitor module suitable for diverse applications. It supervises a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitors and powers a circuit of two-wire smoke detectors.

Built-in type identification automatically identifies this device as a monitor module to the control panel
SEMS screws with clamping plates for ease of wiring
Direct-dial entry of address: 01 – 159
LED indication for normal or off normal indication
Class A supervised wiring to the monitored device

Download Brochure

FZM-1

Zone Interface Monitor Module

The FZM-1 from Honeywell NOTIFIER is an intelligent zone interface monitor module suitable for diverse applications. It supervises a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitors and powers a circuit of two-wire smoke detectors. This standard-sized module monitors and supervises compatible two-wire, 24 volt, smoke detectors on a Style D (Class A) or Style B (Class B) circuit.

Built-in type identification automatically identifies this device as a monitor module to the control panel
SEMS screws with clamping plates for ease of wiring
Direct-dial entry of address: 01 – 159
LED indication for normal or off normal indication
Transmits the status of one zone of 2-wire detectors to the fire alarm control panel
Status conditions are reported as normal, open or alarm

Download Brochure

FDM-1

Dual Monitor Module

The FDM-1 from Honeywell NOTIFIER is a dual-monitor module intended for use in intelligent, two-wire systems. It provides two independent, two-wire initiating device circuits (IDCs) at two separate, consecutive addresses. It is capable of monitoring normally open contact fire alarm and supervisory devices; or either normally open or normally closed security devices. The module has a single panel-controlled LED.

Built-in type identification automatically identifies this device as a monitor module to the control panel
SEMS screws with clamping plates for ease of wiring
Direct-dial entry of address: 01 – 159
LED indication for normal or off normal indication
Monitors two separate Class B circuits

Download Brochure

FMM-101

Intelligent Miniature Monitor Module

The FMM-101 from Honeywell NOTIFIER is an intelligent monitor module suitable for diverse applications. It supervises a circuit of dry-contact input devices, such as conventional heat detectors and pull stations, or monitors and powers a circuit of two-wire smoke detectors.

Built-in type identification automatically identifies this device as a monitor module to the control panel
SEMS screws with clamping plates for ease of wiring
Direct-dial entry of address: 01 – 159
LED indication for normal or off normal indication
Class B supervised wiring to the monitored device
Smaller size fits inside devices or junction boxes

Download Brochure

FDRM-1

All-Weather Vertical Mounting

The FDRM-1 addressable module from Honeywell NOTIFIER is intended for use in intelligent, two-wire loops. It includes two individual relay control modules and two Class B monitor modules. Each relay output is intended for Form C switching applications which do not require wiring supervision for the load circuit. Each monitor input provides an interface between a fire alarm control panel and one or more normally open contact-type devices.

Addressable analogue communication
Sleek, low-profile design
Addresses can be viewed and changed without electronic programmers
Rotary, decimal addressing (1-99 on CLIP systems, 1-159 on FlashScan systems)
Addresses can be viewed and changed without electronic programmers

Download Brochure

FMM-4-20

Analogue Input Module

The FMM-4-20 from Honeywell NOTIFIER is an intelligent addressable analogue input module that allows the NFS2-3030 fire alarm control panel (FACP) to monitor industry-standard, linear-scale, 4–20 mA protocol sensors. The module converts the sensor output to communication protocol that can be interpreted by the FACP for monitoring and display. There are numerous sensors available in the marketplace that communicate using a 4–20 mA output, including gas sensors, temperature sensors, air speed sensors, and more.

FlashScan® operation
Low standby current
Rotary address switches
SEMS screws for easing wiring
Panel controlled status LED (bi-colour)

Download Brochure

FCM-1-REL

Releasing Control Module

The FCM-1-REL Releasing Control Module from Honeywell NOTIFIER uses a redundant protocol; the module must be armed with a pair of signals in order to activate. It will then enter a 3-second window awaiting a pair of confirmation signals. If no confirmation is received, the module will automatically reset. It also supervises the wiring to the connected load and reports the status to the panel as NORMAL, OPEN, or SHORT CIRCUIT. The module has two pairs of output termination points available for fault-tolerant wiring and a panel-controlled LED indicator. The module may be connected to either one 24VDC solenoid or up to two 12VDC solenoids (in series). To ensure proper operation, this module shall be connected to a compatible NOTIFIER system control panel only

FlashScan® operation
Redundant protocol for added protection
Configurable for Class A or Class B operation
External supply voltage monitoring
Can power one 24V or two 12V solenoids
SEMS screws for easing wiring
Panel controlled status LED
Analogue communications
Rotary address switches
Low standby current
Mounts in standard 4" (10.16 cm) junction box

Download Brochure

ISO-X

Isolator Module

Honeywell NOTIFIER’s intelligent addressable isolator module, the ISO-X is used with Fire Alarm Control Panels to protect the system against wire-to-wire short circuits on the Signalling Line Circuit loops. The ISO-6 is a six fault isolator module providing isolation on six equivalent circuits.

Enables part of the communications loop to operate when a short circuit occurs
Automatically resets on correction of short
SEMS screws with clamping plates for ease of wiring

Download Brochure

LDM-32

Lamp Drive Module

Honeywell NOTIFIER’s lamp driver module LDM-32, when combined with a custom graphic display, provides annunciation and control for the NFS-3030, NFS2-3030, NFS-640, AM2020/AFP1010, AFP-300/400, AFP-200, AFP-100, System 5000, and System 500 control panels. It uses a serial communications interface, and may be located up to 6,000 feet from the panel.

Driver module with 32 alarm lamp-driver transistors
ALARM/CIRCUIT ON and TROUBLE lamp/LED per-point option, or more dense alarm-only option (field selectable)
Control switch option for remote control per point
Lamps/LEDs may be programmed to display status of indicating circuits or control relays as well as system status conditions
System trouble lamp/LED signal
On-line/power LED indicator
Alarm and trouble resound with flash of new conditions

Download Brochure

MODBUS-GW

Modbus Gateway

Honeywell NOTIFIER’s Modbus Gateway provides a communication link between networks that use the Modbus/TCP communication protocol and Fire Alarm Control Panels (FACPs) resident on an NFN network. It provides data such as event type, active/inactive, enabled/disabled, acknowledged/unacknowledged, device type, analogue value (4-20ma modules only) and system troubles.

Compatible with standard and high speed NOTI-FIRE-NET
Monitors four compatible NFN nodes (excluding the Modbus gateway)
Supports reads of up to 100 registers at a time. Analogue values can be read 10 registers at a time
UL/ULC Listed

Download Brochure

BACNET-GW-3

BACNet Gateway

The BACNET-GW-3 provides an interface between NOTIFIER’s NOTI•FIRE•NET fire panel network (either the standard or the high-speed version) and a network using the BACnet/IP communication protocol. BACnet protocol is an American National Standard (ANSI/ASHRAE 135-1995). The BACnet Gateway can be connected to a stand-alone ONYX panel with an available network port or it can be connected to NOTI•FIRE•NET.

Compatible with ONYX™ Series panels
Compatible with NOTI•FIRE•NET devices
Monitors up to fourteen NOTI•FIRE•NET panels with a maximum of 15,000 objects (includes all peripherals)
Multiple BACnet Gateways can be used for networks of 15 nodes or more
UL/ULC Listed

Download Brochure

NBG-12LX

Intelligent Pull Station

The NBG-12LX from Honeywell NOTIFIER is an intelligent pull station for use with ONYX Series panels. It is an active fire protection device designed to initiate an alarm on the fire alarm system when activated.

Highly visible for easy identification
Durable polycarbonate material
Simple operation for activation in emergencies

Download Brochure

F/MCP/GLASS

Addressable Manual Call Point

The F/MCP/GLASS Addressable call point from Honeywell NOTIFIER is a non-coded, manual callpoint. It provides NOTIFIER intelligent fire alarm control panels (FACP) with one addressable alarm initiating point. The device is compatible with all NOTIFIER intelligent panels and will automatically operate in F FlashScanTM mode ,which is a patented high-speed communication protocol. The F/MCP/GLASS is designed to provide an interface for causing an alarm on a fire alarm system. A two-wired general connection is used to connect the unit to control panel; this connection allows for both alarm signalling and normal LED operation.

LED status controlled by fire panel
Installable as a flush-mounted device in a normal internal environment

Download Brochure

XAL-53

Explosion-proof pull station

The XAL-53 explosion-proof pull station from Honeywell NOTIFIER is suitable for use in hazardous areas and in applications where emergency control of fire alarm or signal circuits is required. The alarm station is activated by lifting the front cover and pulling down the ring. This quick, easy-to-use two-step process prevents unintentional operation. The operator is reset by depressing the shaft and returning the plate to its original position.

Enclosure is made of copper-free aluminium alloy
Conduit openings are 3/4" (19.05 mm) NPT feed-through
Wiring range is #12 AWG through #24 AWG, solid or stranded

Download Brochure