AMPS-24/E

Addressable Power Supply

Honeywell NOTIFIER’s AMPS-24/E is an addressable power supply and battery charger with up to three 24 VDC outputs. It operates in either FlashScan® or CLIP (Classic Loop Interface Protocol) mode with the NFS-3030/NFS2-3030 Fire Alarm Control Panel (FACP). It can also be used as the primary power supply for the NCA-2 Network Control Annunciator.

HPF24S6E

The HPF24S6(C/E) is a compact, cost-effective, 6-amp remote power supply with battery charger. It may be connected to any 12- or 24-volt Fire Alarm Control Panel (FACP) or may stand alone. Primary applications include Notification Appliance (bell) Circuit (NAC) expansion (to support ADA requirements and NAC synchronisation) or auxiliary power to support 24-volt system accessories.

ACPS-610(E)

Addressable Charger/Auxiliary Power Supply

The ACPS-610(E) is an auxiliary power supply with a battery charging option and a host of special features. Selectable charging options allow the ACPS-610 to provide 6 amps of shared power to four outputs while charging batteries from 12 to 200 AH, or 10 amps of shared power when the unit is configured for use with an external battery charger.

ACM-24AT

ACS Series Annunciator

The ONYX® Series ACS Annunciators provide a modular line of products for annunciation and control of the NOTIFIER ONYX® Series Intelligent Fire Alarm Control Panels, Network Control Annunciators, and NOTIFIER’s legacy addressable panels. The ACS line provides arrays of LEDs to indicate point status and, in some versions, switches to control the state of output circuits. The ACM-24AT contains 24 colour-programmable (red/green/yellow) Active and 24 yellow Trouble LEDs, 24 momentary touch-pad switches, a System Trouble LED, an On-Line/Power LED, and a local piezo sounder with a silence/acknowledge switch for audible indication of alarm and trouble conditions.

• Speaker control mode for use with XPIQ and the following panels: NFS-3030, NFS2-3030, NFS-640, NFS2-640, AM2020, AFP1010, AFP-400, AFP-300
• Compatible with existing annunciators
• On-board end-of-line resistors can be enabled/disabled by setting a switch
• Alarm/Circuit On and Trouble LED per-point option or more dense Alarm-only option
• Touch-pad control switch option for remote control of system relays; or silence, reset, and evacuate
• LED indicators: System Trouble, Online/Power
• Alarm and trouble resound with flash of new conditions

AEM-24AT

ACS Series Annunciator

The ONYX® Series ACS Annunciators provide a modular line of products for annunciation and control of the NOTIFIER ONYX® Series Intelligent Fire Alarm Control Panels, Network Control Annunciators, and NOTIFIER’s legacy addressable panels. The ACS line provides arrays of LEDs to indicate point status and, in some versions, switches to control the state of output circuits. The AEM-24AT expands the ACM-24AT by 24 system points. It is identical in size and in frontal appearance to the ACM-24AT. Up to three of these expander modules can be supported by an ACM-24AT, for a maximum of 96 system points.

• Speaker control mode for use with XPIQ and the following panels: NFS-3030, NFS2-3030, NFS-640, NFS2-640, AM2020, AFP1010, AFP-400, AFP-300
• Compatible with existing annunciators
• On-board end-of-line resistors can be enabled/disabled by setting a switch
• Alarm/Circuit On and Trouble LED per-point option or more dense Alarm-only option
• Touch-pad control switch option for remote control of system relays; or silence, reset, and evacuate
• LED indicators: System Trouble, Online/Power
• Alarm and trouble resound with flash of new conditions

ACM-48A

ACS Series Annunciator

The ONYX® Series ACS Annunciators provide a modular line of products for annunciation and control of the NOTIFIER ONYX® Series Intelligent Fire Alarm Control Panels, Network Control Annunciators, and NOTIFIER’s legacy addressable panels. The ACS line provides arrays of LEDs to indicate point status and, in some versions, switches to control the state of output circuits. The ACM-48A contains 48 colour-programmable (red/green/yellow) Active LEDs, a System Trouble LED, an On-Line/Power LED and a local piezo sounder with a Silence/Acknowledge switch for audible indication of alarm and trouble conditions.

• Speaker control mode for use with XPIQ and the following panels: NFS-3030, NFS2-3030, NFS-640, NFS2-640, AM2020, AFP1010, AFP-400, AFP-300
• Compatible with existing annunciators
• On-board end-of-line resistors can be enabled/disabled by setting a switch
• Alarm/Circuit On and Trouble LED per-point option or more dense Alarm-only option
• Touch-pad control switch option for remote control of system relays; or silence, reset, and evacuate
• LED indicators: System Trouble, Online/Power
• Alarm and trouble resound with flash of new conditions

AEM-48A

ACS Series Annunciator

The ONYX® Series ACS Annunciators provide a modular line of products for annunciation and control of the NOTIFIER ONYX® Series Intelligent Fire Alarm Control Panels, Network Control Annunciators, and NOTIFIER’s legacy addressable panels. The ACS line provides arrays of LEDs to indicate point status and, in some versions, switches to control the state of output circuits. The AEM-48A expands the ACM-48A by 48 system points. It is identical in size and in frontal appearance to the ACM-48A. One expander module can be supported by an ACM-48A, for a maximum of 96 system points.

• Speaker control mode for use with XPIQ and the following panels: NFS-3030, NFS2-3030, NFS-640, NFS2-640, AM2020, AFP1010, AFP-400, AFP-300
• Compatible with existing annunciators
• On-board end-of-line resistors can be enabled/disabled by setting a switch
• Alarm/Circuit On and Trouble LED per-point option or more dense Alarm-only option
• Touch-pad control switch option for remote control of system relays; or silence, reset, and evacuate
• LED indicators: System Trouble, Online/Power
• Alarm and trouble resound with flash of new conditions

NCA-2

ACS Series Annunciator

The ONYX® Series ACS Annunciators provide a modular line of products for annunciation and control of the NOTIFIER ONYX® Series Intelligent Fire Alarm Control Panels, Network Control Annunciators, and NOTIFIER’s legacy addressable panels. The ACS line provides arrays of LEDs to indicate point status and, in some versions, switches to control the state of output circuits. The AEM-48A expands the ACM-48A by 48 system points. It is identical in size and in frontal appearance to the ACM-48A. One expander module can be supported by an ACM-48A, for a maximum of 96 system points.

• Speaker control mode for use with XPIQ and the following panels: NFS-3030, NFS2-3030, NFS-640, NFS2-640, AM2020, AFP1010, AFP-400, AFP-300
• Compatible with existing annunciators
• On-board end-of-line resistors can be enabled/disabled by setting a switch
• Alarm/Circuit On and Trouble LED per-point option or more dense Alarm-only option
• Touch-pad control switch option for remote control of system relays; or silence, reset, and evacuate
• LED indicators: System Trouble, Online/Power
• Alarm and trouble resound with flash of new conditions

LCD2-80

Liquid Crystal Display

The LCD2-80 is an 80-character, backlit LCD display annunciator for the NOTIFIER NFS2-640, NFS2-3030, NFS-320, NCA-2 and legacy panels that supported the LCD-80/LCD-80TM. The NFS2-3030 and the NCA-2 also support LCD2-80s when set for LCD-80 supervision. Up to 32 LCD2-80s can annunciate and provide remote reset, acknowledge, drill and silence of the control panel from remote locations.

• LEDS for general off-normal events with UL 864 9th Edition panels
• Control switches for System Acknowledge, Signal Silence Drill and System Reset
• Display mimics panel or NCA:
  • Event message
  • 20 characters for point label
  • 12 characters for extended label
  • Time, date and point ad
• Up to 6000 foot segments between units
• Local piezo sounder with alarm/trouble resound
• Displays all analogue, addressable points

LCD-160

Liquid Crystal Display

The LCD-160, 640-character Liquid Crystal Display (LCD) annunciator and remote control for the NOTIFIER NFS-3030/ NFS2-3030 Fire Alarm Control Panel (FACP). The LCD-160 will mimic the top portion (160 characters) of the NFS-3030/ NFS2-3030’s 640-character display. This provides the event and pre-programmed custom messages as displayed on the main panel. The full screen contains soft key functions, and can display other panel information

• 640-character Liquid Crystal Display with backlit control
• RDP bus can drive up to 32 RDP devices
• Input for AKS-1B key switch

LCM-320

Loop Control Module

The LCM-320 Loop Control Module provides NOTIFIER’s ONYX® NFS2-640 and NFS2-3030 Fire Alarm Control Panels with additional Signalling Line Circuits.

• Up to 12,500 feet (3,810 m) on a Class B (Style 4) SLC loop (twisted-unshielded)
• Built-in degraded mode increases survivability
• Very simple installation — plug-in style
• Permits multiple loops in small enclosure

LEM-320

Loop Control Module

The LEM-320 Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM320s and five LEM-320s. The LEM-320 module is used to expand the NFS-640/NFS2-640 to a second loop, and to expand each LCM-320 used on the NFS-3030/NFS2-3030 — each NFS-3030/NFS2-3030 LCM-320 supports an expansion LEM-320.

• Up to 12,500 feet (3,810 m) on a Class B (Style 4) SLC loop (twisted-unshielded)
• Built-in degraded mode increases survivability
• Very simple installation — plug-in style
• Permits multiple loops in small enclosure

HS-NCM-W

Loop Control Module

The High-Speed Network Communications Module (HS-NCM-W) provides NOTIFIER’s NFS-320, NFS-640, NFS2-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, NCA and NCA-2 Network Control Annunciators, and DVC Digital Voice Command with a means to connect to High-Speed NOTI•FIRE•NET™. It is meant for connecting nodes with twisted-pair wire and can accommodate up to 2 node addresses.

• Supports twisted-pair wire medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Transformer coupling provides electrical isolation between nodes
• Pluggable terminal wiring with strain relief
• Pluggable service connector (feeds signal directly through) in the event that power must be removed from a node
• 12 Mb transmission rate
• Data is regenerated at each node
• Two network ports to allow simultaneous connection to fire alarm control panel and to programming computer

HS-NCM-MF

Loop Control Module

The High-Speed Network Communications Module (HS-NCM-MF) provides NOTIFIER’s NFS-320, NFS-640, NFS2-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, NCA and NCA-2 Network Control Annunciators, and DVC Digital Voice Command with a means to connect to High-Speed NOTI•FIRE•NET™. It is meant for connecting nodes with multi-mode fibre-optic cable.

• Supports fibre-optic medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Data is immune to all environmental noise
• Optical isolation prevents ground loops
• Data is regenerated at each node
• Two network ports to allow simultaneous connection to fire alarm control panel and to programming computer
• Enables software and database upload/download over High-Speed NOTI•FIRE•NET™

HS-NCM-MF

Loop Control Module

The High-Speed Network Communications Module (HS-NCM-SF) provides NOTIFIER’s NFS-320, NFS-640, NFS2-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, NCA and NCA-2 Network Control Annunciators, and DVC Digital Voice Command with a means to connect to High-Speed NOTI•FIRE•NET™. It is meant for connecting nodes with single-mode fibre-optic cable.

• Supports fibre-optic medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Data is immune to all environmental noise
• Optical isolation prevents ground loops
• Data is regenerated at each node
• Two network ports to allow simultaneous connection to fire alarm control panel and to programming computer
• Enables software and database upload/download over High-Speed NOTI•FIRE•NET™

HS-NCM-WMF

Loop Control Module

The High-Speed Network Communications Module (HS-NCM-WMF) provides NOTIFIER’s NFS-320, NFS-640, NFS2-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, NCA and NCA-2 Network Control Annunciators, and DVC Digital Voice Command with a means to connect to High-Speed NOTI•FIRE•NET™. It is meant for connecting wire and multimode fibre-optic medium on the same network.

• Supports twisted-pair wire and fibre-optic medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Allows wire and fibre optic nodes to communicate as one network
• Data is regenerated at each node
• Two network ports to allow simultaneous connection to fire alarm control panel and to programming computer
• Enables software and database upload/download over High-Speed NOTI•FIRE•NET™

HS-NCM-WSF

Loop Control Module

The High-Speed Network Communications Module (HS-NCM-WSF) provides NOTIFIER’s NFS-320, NFS-640, NFS2-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, NCA and NCA-2 Network Control Annunciators, and DVC Digital Voice Command with a means to connect to High-Speed NOTI•FIRE•NET™. It is meant for connecting wire and single-mode fibre-optic mediums on the same network.

• Supports twisted-pair wire and fibre-optic medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Allows wire and fibre optic nodes to communicate as one network
• Data is regenerated at each node
• Two network ports to allow simultaneous connection to fire alarm control panel and to programming computer
• Enables software and database upload/download over High-Speed NOTI•FIRE•NET™

HS-NCM-MFSF

Loop Control Module

The High-Speed Network Communications Module (HS-NCM-MFSF) provides NOTIFIER’s NFS-320, NFS-640, NFS2-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, NCA and NCA-2 Network Control Annunciators, and DVC Digital Voice Command with a means to connect to High-Speed NOTI•FIRE•NET™. It is meant for connecting multimode and single-mode fibre optic mediums on the same network.

• Supports twisted-pair wire and fibre-optic medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Allows wire and fibre optic nodes to communicate as one network
• Data is regenerated at each node
• Two network ports to allow simultaneous connection to fire alarm control panel and to programming computer
• Enables software and database upload/download over High-Speed NOTI•FIRE•NET™

NCM-W

Network Communications Module

The Network Communications Module (NCM-W) provides NOTIFIER’s NFS-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, and NCA and NCA-2 Network Control Annunciators with a means to connect to NOTI•FIRE•NET™. It is meant for connecting nodes with twisted-pair wire. Supports twisted-pair wire medium.

• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Two programmable data thresholds
• Transformer coupling provides electrical isolation between nodes
• Pluggable terminal wiring with strain relief
• Pluggable service connector (feeds signal directly through) in the event that power must be removed from a node
• 312.5 Kbaud transmission rate
• Data is regenerated at each node

NCM-F

Network Communications Module

The Network Communications Module (NCM-F) provides NOTIFIER’s NFS-640, NFS-3030, and NFS2-3030 Fire Alarm Control Panels, and NCA and NCA-2 Network Control Annunciators with a means to connect to NOTI•FIRE•NET™. It is meant for connecting nodes with fibre-optic cable.

• Supports fibre-optic medium
• NFPA Style 4 (Class B) operation or NFPA Style 7 (Class A) operation
• Data is immune to all environmental noise
• Optical isolation prevents ground loops
• 312.5 Kbaud transmission rate
• Data is regenerated at each node

NCD

Network Communications Module

The Network Control Display (NCD) is the next-generation of network control annunciators for the NOTIFIER Systems. With a new modern contemporary design, the NCD meets today's building aesthetic needs. The intuitive colour 10” touch screen provides colour-coded information of detailed system status and point information. It is compatible with ONYX Series nodes as well as the NCA-2. The NCD provides system control and display capabilities for selected or all network nodes, with updated display features to match building aesthetics and user security requirements. The NCD can be used as the primary display for ONYX Series FACP's by utilising Direct Connect. When connected to one or more networked panels the NCD provides network control and status display capabilities

• Quick identification of event information
• Interactive Summary Event Count Display
• Intuitive user guidance programme
• Environmental adjustment controls to maximise LCD legibility
• Full supervision of all inputs and network integrity

RP-2001(E)

Network Communications Module

The RP-2001 is a six-zone FACP for single and dual hazard deluge and preaction applications. The RP-2001 provides reliable fire detection, signaling and protection for commercial, industrial and institutional buildings requiring water-based releasing. The RP-2001 is compatible with System Sensor’s i3 detectors which are conventional smoke detectors that can transmit a maintenance trouble signal to the FACP indicating the need for cleaning and a supervisory ‘freeze’ signal when the ambient temperature falls below the detector rating of approximately 45°F (7.22°C)

RP-2002(E)

Network Communications Module

The RP-2002(E) from Honeywell NOTIFIER is a UL listed six-zone fire alarm control panel for single and dual-hazard deluge and preaction applications. It provides fire detection, signalling and protection for commercial, industrial and institutional buildings requiring water-based releasing.